Computer Networks — NCERT Solutions

a) Each node is connected with the help of a single cable.

→ This is Bus Topology.

Reason: In bus topology, all nodes share a single common backbone cable (called the bus). Data sent by any node travels along this single cable and can be received by all other nodes.

b) Each node is connected with central switching through independent cables.

→ This is Star Topology.

Reason: In star topology, each communicating device (node) is connected to a central networking device (hub or switch) through its own independent cable. All communication between nodes passes through this central device.

Definition of Modem:
Modem stands for MOdulator DEModulator. It is a hardware device used for conversion between the digital data (used by computers) and analog signals (used for transmission over telephone lines or cable lines).

Working:

• Modulation: The modem converts digital data (0s and 1s) from the computer into analog signals for transmission over the telephone line.
• Demodulation: At the receiving end, the modem converts the incoming analog signals back into digital data that the computer can understand.

Why is it used?
A modem is used to:

1. Connect a computer or a local network to the Internet through a telephone line, cable line, or DSL line.
2. Enable data communication between computers over long distances using existing telephone infrastructure.
3. Allow broadband Internet access in homes and offices.

Conclusion: A modem acts as a bridge between the digital world of computers and the analog world of communication lines, enabling Internet connectivity.

a) Switch:
A switch is a networking device used to connect multiple computers or communicating devices in a LAN. When a data packet arrives, the switch reads the destination MAC address from the packet and looks it up in its internal table to determine which port to send it to. Thus, it sends data only to the intended device (unlike a hub which broadcasts to all). A switch can forward multiple packets simultaneously and drops noisy or corrupted signals, asking the sender to resend.

b) Repeater:
A repeater is an analog networking device that regenerates and amplifies weak signals on a cable. Data signals lose their strength after travelling a certain distance (usually about 100 m). The repeater receives the weakened signal, regenerates it to its original strength, and puts it back on the cable, thus extending the range of the network.

c) Router:
A router is a network device that receives data packets, analyses them, and forwards them to the appropriate network. It connects two or more different networks (e.g., a LAN to the Internet). A router uses IP addresses to determine the best path for forwarding data packets. It is more intelligent than a switch as it can make routing decisions based on network conditions.

d) Gateway:
A gateway serves as the entry and exit point of a network. All data coming into or going out of a network must pass through the gateway. It connects two networks that may use different protocols and translates between them. For example, a gateway connects a corporate LAN to the Internet. It performs protocol conversion, making communication between dissimilar networks possible.

e) NIC (Network Interface Card):
A NIC (Network Interface Card), also called an Ethernet card, is a network adaptor installed in a computer that allows it to connect to a network. It provides the physical interface between the computer and the network cable (or wireless signal). Each NIC has a unique MAC (Media Access Control) address permanently assigned to it, which helps in uniquely identifying the computer on the network.

(Note: As this is a drawing-based question, the layouts are described textually with ASCII representations.)

Star Topology (5 computers):

In star topology, all five computers (PC1 to PC5) are connected to a central switch/hub.

        PC1
         |
 PC5 — Switch/Hub — PC2
         |
        PC3
         |
        PC4

Description: Each of the five computers (PC1, PC2, PC3, PC4, PC5) is connected to the central switch or hub through its own independent cable. All communication passes through the central device.

Bus Topology (5 computers):

In bus topology, all five computers are connected to a single common backbone cable (bus) with terminators at both ends.

Terminator —|— PC1 —|— PC2 —|— PC3 —|— PC4 —|— PC5 —|— Terminator
             (Single Backbone Bus Cable)

Description: All five computers (PC1 to PC5) are connected to a single shared cable. Terminators are placed at both ends of the bus to prevent signal reflection. Data sent by any computer travels along the entire bus and can be received by all other computers.

MAC Address — Significance:

Definition: The MAC (Media Access Control) address, also known as the physical address or hardware address, is a unique, permanent address associated with a Network Interface Card (NIC).

Significance of MAC Address:

1. Unique Identification: Every NIC in the world has a unique MAC address (48-bit address, written as 6 pairs of hexadecimal digits, e.g., 00:1A:2B:3C:4D:5E). This uniquely identifies each device on a network.

2. Physical Layer Communication: MAC addresses are used at the Data Link Layer of the network to ensure data is delivered to the correct device within a local network (LAN).

3. Permanent Address: Unlike an IP address, a MAC address is permanently assigned by the manufacturer and does not change when the device moves to a different network.

4. Used by Switches: Network switches use MAC addresses to build their address tables and forward data frames only to the correct destination port.

5. Security: MAC address filtering can be used in wireless networks to allow only specific devices to connect, enhancing network security.

Conclusion: The MAC address is essential for the physical identification and communication of devices within a local network.

Difference between IP Address and MAC Address:

Conclusion: The MAC address is a permanent, hardware-level identifier used for local communication, while the IP address is a logical, changeable identifier used for communication across networks and the Internet.

DNS — Domain Name System:

DNS (Domain Name System) is a system that translates human-readable domain names (like www.google.com) into their corresponding IP addresses (like 142.250.182.46) that computers use to identify each other on the network. This process is called domain name resolution.

Why is DNS needed?
Computers communicate using IP addresses (numbers), but humans find it easier to remember domain names (words). DNS acts as a "phone book" of the Internet, converting domain names to IP addresses automatically.

How it works:

1. A user types a URL (e.g., www.example.com) in the browser.
2. The HTTP protocol contacts a DNS server to find the IP address for that domain name.
3. The DNS server returns the corresponding IP address.
4. The browser uses this IP address to connect to the web server and load the website.

DNS Server:
A DNS server is a computer server that maintains a database of domain names and their corresponding IP addresses. When a browser requests the IP address for a domain name, the DNS server looks it up in its database and responds with the correct IP address.

Hierarchy of DNS Servers:

• DNS servers are arranged in a hierarchical order.
• At the top level, there are 13 root servers.
• Below them are other DNS servers at different levels.
• If a DNS server does not have the entry for a domain, it forwards the request to another DNS server higher in the hierarchy.

Conclusion: DNS is the backbone of Internet navigation, and DNS servers make it possible to use easy-to-remember domain names instead of numeric IP addresses.

Explanation for Sahil:

The Internet and the World Wide Web (WWW) are related but different concepts. Many people use these terms interchangeably, but they are not the same.

Internet:

• The Internet is the global network of computing devices (computers, smartphones, servers, etc.) connected to each other.
• It is the physical infrastructure — the hardware, cables, routers, and protocols — that connects billions of devices worldwide.
• The Internet supports many services, not just the Web. These include e-mail, file transfer (FTP), online gaming, video conferencing, VoIP (voice calls), etc.
• The Internet is the largest WAN in the world.

Example of Internet: When you send an e-mail using Gmail, or make a video call on WhatsApp, you are using the Internet (but not necessarily the World Wide Web).

World Wide Web (WWW):

• The World Wide Web (WWW), or simply the Web, is a collection of information stored in the form of trillions of interlinked web pages and web resources that can be accessed via the Internet.
• It is a service that runs on top of the Internet.
• Web pages are written in HTML, identified by URLs, and accessed using the HTTP/HTTPS protocol through a web browser.
• The WWW was invented by Sir Tim Berners-Lee in 1990.

Example of WWW: When you open a web browser and visit www.ncert.nic.in to read a textbook, you are using the World Wide Web.

Simple Analogy:
Think of the Internet as a road network (the infrastructure), and the World Wide Web as the vehicles and destinations (the content and services) that travel on those roads.

Key Difference in one line:
> The Internet is the network (infrastructure), while the World Wide Web is a service (information system) that uses the Internet.